F7-E40 Luminescent Flat Stair Nosing IL-F7-E4
Our high performance F7-E40 Photoluminescent Anodized Flat Stair Nosing provides step edge visibility and enhances egress speeds in all lighting conditions, creating a safe, and efficient egress path in any facility. Our stair strips can be installed on a range of materials to meet the needs of any project, including concrete, timber, steel, tiles, and checker plate stairs. Alone, this product brightly illuminates stairways in any egress pathway, and can be used in conjunction with illuminated exit signs in order to create a safe path to the exit discharge of any facility. Through providing step edge contrast, stellar visibility in all light conditions, slip resistance, and wear-resistant, Ecoglo®’s F7-E40 Photoluminescent Anodized Flat Stair Nosing will provide your facility with a four-pronged solution to pathfinding needs. Our non-slip stair nosing not only meets code compliance, but exceeds luminous egress requirements set out in local and international building, fire and life safety codes. The safety of all people in a facility depends on a clear egress plan and advance site preparation including clear marking of escape routes. Photoluminescent egress marking systems installed in exit stairwells are a critical, code-required component of any building safety system. Photoluminescent markings are always on, full proof systems to guide people out of buildings during any type of emergency conditions. Charges with ambient light. Always-on visible light. No electricity required. Our photoluminescent systems are comprised of materials including aluminum, epoxies, PVC, tapes, and paints . A one-inch wide "glowing" stripe is applied to the leading edge the steps, on handrails, and along the perimeter of landings and pathways leading out of the building. General Information Install these stair strips with polyurethane adhesive and mechanical fasteners, or solely adhesive. We supply these products with pre-drilled countersunk holes for your convenience, including stainless steel fasteners and concrete nylon anchors. The standard location for these holes is 2” from each end and approximately 12” apart. The standard lengths of our stair strips are 8ft and 10ft, but they are also available in cut-to-length sizes (Tolerance + or – 1/8”) Inserts are supplied unattached but will be easily installed over the mechanical fasteners using a polyurethane adhesive (which is included). Inserts can be cut using a shear, while aluminum nosings are cut with a saw. Do not cut inserts with a saw as it will damage the saw blade. Weight: 0.416 lbs/ft. Aluminum Finish Available in Clear Anodized Aluminum Finish Black, Light Bronze and, Dark Bronze Anodize finishes are available at an additional cost
F7-E30 Luminescent Flat Stair Nosing IL-F7-E3
Rely on Ecoglo®’s F7-E30 Photoluminescent Anodized Flat Stair Nosing to provide excellent step-edge visibility and enhances egress speeds in all lighting conditions. Our expertly engineered photoluminescent strip is integrally bonded into the aluminum stair nosing, along with a non-slip strip, which provides a stark color contrast, further enhancing step edge visibility. After the power fails in your facility, rely on this luminous egress path marking product to cut through shadows and provide a bright, easy to follow source of egress lighting. The sleek aluminum profile of Ecoglo®’s stair nosing provides a modern look to any facility, without distracting from the facility’s design. To best meet the needs of any project, our metal stair nosing can easily be installed on a range of substrates, such as concrete, timber, tile, steel and checker plate. The safety of all people in a facility depends on a clear egress plan and advance site preparation including clear marking of escape routes. Photoluminescent egress marking systems installed in exit stairwells are a critical, code-required component of any building safety system. Photoluminescent markings are always on, full proof systems to guide people out of buildings during any type of emergency conditions. Charges with ambient light. Always-on visible light. No electricity required. Our photoluminescent systems are comprised of materials including aluminum, epoxies, PVC, tapes, and paints . A one-inch wide "glowing" stripe is applied to the leading edge the steps, on handrails, and along the perimeter of landings and pathways leading out of the building. General Information Install with polyurethane adhesive and mechanical fasteners, or adhesive only. Supply with pre-drilled countersunk holes. Includes stainless steel fasteners and concrete nylon anchors. Standard location is 2″ from each end and approx. 12″ apart. Available in cut to length sizes. (Tolerance +or- 1/8”) Standard lengths are 8ft and 10ft. Inserts are supplied unattached. Inserts are installed over the mechanical fasteners using a polyurethane adhesive (included). Inserts can be cut using a shear. Aluminum nosings are cut with a saw. Cutting inserts with saw will damage the saw blade. Weight: 0.439 lbs/ft. Aluminum Finish Available in Clear Anodized Aluminum Finish Black, Light Bronze and, Dark Bronze Anodize finishes are available at an additional cost
F6-E20 Luminescent Flat Stair Nosing IL-F6
The F6-E20 Photluminescent Flat Stair Nosing provides an extra level of safety, without distracting from the design of your building. The sleek aluminum profile modernizes and renovates any facility, while keeping occupants safe. Ecoglo®’s expertly engineered photoluminescent strip has been integrally bonded into this aluminum stair nosing to provide a reliable source of egress lighting. Simply gaining a charge from either a natural or artificial light source, this luminous egress path marking product is ready to glow brightly for hours after the power has failed. To best serve your project needs, Ecoglo®’s aluminum stair nosing can easily be installed on a range of substrates including concrete, timber, tiles, steel, checker plate and thin carpet. The safety of all people in a facility depends on a clear egress plan and advance site preparation including clear marking of escape routes. Photoluminescent egress marking systems installed in exit stairwells are a critical, code-required component of any building safety system. Photoluminescent markings are always on, full proof systems to guide people out of buildings during any type of emergency conditions. Charges with ambient light. Always-on visible light. No electricity required. Our photoluminescent systems are comprised of materials including aluminum, epoxies, PVC, tapes, and paints . A one-inch wide "glowing" stripe is applied to the leading edge the steps, on handrails, and along the perimeter of landings and pathways leading out of the building. General Information Install with polyurethane adhesive and mechanical fasteners, or adhesive only. Supplied with pre-drilled countersunk holes. Includes stainless steel fasteners and concrete nylon anchors. Standard location is 2″ from each end and approx. 12″ apart. Available in cut to length sizes. (Tolerance +or- 1/8”) Standard lengths are 8ft and 10ft. Inserts Attached or Unattached – Unattached is recommended for on-site cutting. Inserts are installed with a premium polyurethane adhesive. Weight: 0.46 lbs/ft. Aluminum Finish Available in Clear Anodized Aluminum Finish Black, Light Bronze and, Dark Bronze Anodize finishes are available at an additional cost
F4-E20 Luminescent flat Stair Nosing IL-F4
Ecoglo®’s expertly engineered F4-E20 Photoluminescent Anodized Flat Stair Nosing is designed to enhance egress speeds in all lighting conditions and provide exceptional step-edge visibility. After gaining a full charge from exposure to either a natural or artificial light source, the integrally bonded photoluminescent brightly lights stairways after the power has gone out to safely guide occupants to the exit discharge. This versatile non-slip aluminum stair nosings can be installed on a variety of substrates such as concrete, timber, tiles, checker plate, steel and thin carpet. Our patented manufacturing process brings you the very best in luminescent properties, ensuring you have a luminous egress product you can trust. The safety of all people in a facility depends on a clear egress plan and advance site preparation including clear marking of escape routes. Photoluminescent egress marking systems installed in exit stairwells are a critical, code-required component of any building safety system. Photoluminescent markings are always on, full proof systems to guide people out of buildings during any type of emergency conditions. Charges with ambient light. Always-on visible light. No electricity required. Our photoluminescent systems are comprised of materials including aluminum, epoxies, PVC, tapes, and paints . A one-inch wide "glowing" stripe is applied to the leading edge the steps, on handrails, and along the perimeter of landings and pathways leading out of the building. General Information Install our stair strips using polyurethane adhesive and mechanical fasteners. The product can also be installed using only the adhesive. This metal stair nosing comes supplied with pre-drilled countersunk holes, including stainless steel fasteners and concrete nylon anchors. The standard hole is located 2” from each end and approximately 12” apart. The standard lengths for our metal stair nosing are 8ft and 10ft, but this illuminated stair nosing is also available in cut to length sizes (Tolerance + or – 1/8”). Inserts can come Attached or Unattached – Unattached is recommended for on-site cutting. Use premium polyurethane adhesive to install Ecoglo® inserts. This egress signage weighs 0.44 lbs/ft. Aluminum Finish: This abrasive stair nosing is available in 6063 – T5 Aluminum, Mill Finish, or with Clear or Black Anodized Finish (Anodized to Type 2, Class 1. 20 microns thickness). Light Bronze and Dark Bronze Anodized finishes are available at an additional cost.